🔧 Edge - Engine Air Filter Replacement

Changing the engine air filter on your Edge helps the turbocharged 2.0L engine breathe clean air and protects it from dust and debris. This is a great beginner repair because the filter housing is easy to access and does not require lifting the vehicle.

Difficulty Level: Beginner | Estimated Time: 10-20 minutes

---

⚠️ Safety & Precautions

• ⚠️ Let the engine cool before working near the air intake box.
• ⚠️ Keep dirt, leaves, and loose debris out of the open air filter housing.
• ⚠️ Do not start the engine while the air filter is removed.
• ⚠️ Battery disconnect is not required for this repair.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 8mm socket
• 1/4-inch ratchet
• Flathead screwdriver
• Shop vacuum
• Microfiber towel
• Nitrile gloves
• Safety glasses

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Engine air filter - Qty: 1

---

📋 Before You Begin

• 🅿️ Park your Edge on level ground and set the parking brake.
• 🔥 Turn the engine off and let it cool for at least 10 minutes.
• 🔑 Remove the key from the vehicle or keep the key fob away from the cabin.
• 💡 Open the hood and make sure it is fully supported.
• 📦 The air filter box is on the driver-side front area of the engine bay, connected to the black intake tube.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Locate the Air Filter Housing

• Use your hands to identify the black plastic air filter housing near the driver-side front of the engine bay.
• The housing connects to the intake tube that leads toward the engine.
• Take a photo before disassembly.

Step 2: Loosen the Air Filter Housing Fasteners

• Use an 8mm socket and 1/4-inch ratchet to loosen the air filter housing screws.
• These screws are usually retained in the lid, meaning they stay attached and do not fully come out.
• If a screw is tight, use a flathead screwdriver gently only if the screw head allows it.
• No torque spec is required for removal.

Step 3: Lift the Air Filter Housing Lid

• Use your hands to carefully lift the upper half of the air filter housing.
• Do not force the lid or pull hard on the attached intake tube.
• You only need enough space to slide the old filter out.
• Plastic tabs can break if forced.

Step 4: Remove the Old Engine Air Filter

• Use your hands to lift the old engine air filter straight out of the lower air box.
• Notice the direction and shape of the old filter before removing it fully.
• Check the old filter for heavy dirt, leaves, oil, or signs of rodent nesting.

Step 5: Clean the Air Box

• Use a shop vacuum to remove loose dirt, leaves, or debris from the lower air filter box.
• Use a microfiber towel to wipe the inside edge where the filter seal sits.
• Do not push dirt into the intake tube opening.
• A shop vacuum is a small vacuum used to safely remove dry debris from the work area.

Step 6: Install the New Engine Air Filter

• Use your hands to place the new engine air filter into the lower housing.
• Make sure the rubber seal sits flat all the way around the filter box.
• The filter should drop into place without bending or forcing it.
• A pinched seal lets dirt past.

Step 7: Reinstall the Air Filter Housing Lid

• Use your hands to lower the housing lid back into place.
• Make sure the lid sits evenly and does not trap the filter edge.
• Check that any tabs or locating edges are properly seated before tightening screws.

Step 8: Tighten the Housing Screws

• Use an 8mm socket and 1/4-inch ratchet to tighten the air filter housing screws evenly.
• Tighten until snug only; do not overtighten plastic housing screws.
• Torque to snug by hand only; Ford does not require a high torque value for these plastic air box fasteners.

Step 9: Final Visual Check

• Use a flashlight if available to inspect the housing seam all the way around.
• Confirm the intake tube is still attached and the housing lid is fully closed.
• Remove all tools and towels from the engine bay before closing the hood.

---

✅ After Repair

• ✅ Start your Edge and let it idle for 30-60 seconds.
• ✅ Listen for hissing or whistling near the air filter box, which can mean the lid is not seated correctly.
• ✅ If the engine idle sounds normal and no warning lights appear, the repair is complete.
• ✅ Replace the engine air filter more often if you drive in dusty conditions.

---

💰 DIY vs Shop Cost

Shop Cost: $60-$120 parts + labor

DIY Cost: $15-$35 parts only

You Save: $45-$85 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.2-0.4 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.