How to Replace the Cabin Air Filter on a 2005-2015 Hyundai Tucson (Trim: Limited | Engine: Inline 4 2.4L | Body: Sport Utility)
Step-by-step DIY instructions with tools, filter location, airflow direction, and safety tips for 2005, 2011, 2012, 2013
How to Replace the Cabin Air Filter on a 2005-2015 Hyundai Tucson (Trim: Limited | Engine: Inline 4 2.4L | Body: Sport Utility)
Step-by-step DIY instructions with tools, filter location, airflow direction, and safety tips for 2005, 2011, 2012, 2013
🔧 Tucson - Cabin Air Filter Replacement
Replacing the cabin air filter on your Tucson is a simple beginner-friendly job. The filter sits behind the glove box and cleans dust, pollen, and odors from the air coming through your vents.
Difficulty Level: Beginner | Estimated Time: 10-20 minutes
🔧 Required Tools
You'll need the following tools for this repair:
- Safety glasses
- Nitrile gloves
- Flashlight
🔩 Required Parts
HowToo sells all the parts you need for this repair:
- Cabin air filter - Qty: 1
📋 Before You Begin
- Park your Tucson on level ground.
- Turn the ignition off and remove the key.
- Empty the glove box so items do not fall out.
- No battery disconnect is required for this repair.
- A cabin air filter is a rectangular paper or carbon filter that slides into the HVAC air box behind the glove box.
🔨 Step-by-Step Instructions
Follow these steps in order:
Step 1: Open and Empty the Glove Box
- Use your hands to open the glove box fully.
- Remove all contents from the glove box.
- Use a flashlight if the area is dim.
- Put items in a small bag.
Step 2: Release the Glove Box Stops
- Use your hands to locate the round stop knobs on the inside left and right sides of the glove box.
- Turn each stop knob counterclockwise about a quarter turn.
- Pull the stop knobs inward and remove them from the glove box.
- Support the glove box with one hand so it does not drop suddenly.
Step 3: Disconnect the Glove Box Damper
- Use your hands to find the small damper arm on the right side of the glove box.
- A damper is a small slow-drop arm that keeps the glove box from falling open too quickly.
- Gently slide the damper arm off its pin.
- Lower the glove box down toward the floor.
Step 4: Remove the Cabin Filter Cover
- Use your flashlight to look behind the lowered glove box.
- Find the long rectangular cabin filter cover on the HVAC housing.
- Use your hands to pinch the cover tabs inward.
- Pull the cover straight out and set it aside.
Step 5: Remove the Old Cabin Air Filter
- Use your hands to slide the old cabin air filter straight out.
- Watch the airflow arrow printed on the old filter before removing it completely.
- On your Tucson, install the new filter with the airflow arrow pointing downward.
- Dust may fall out slowly.
Step 6: Install the New Cabin Air Filter
- Use your hands to slide the new cabin air filter into the filter slot.
- Make sure the airflow arrow on the filter points downward.
- Push it in gently until it is fully seated.
- Do not crush or fold the filter edges.
Step 7: Reinstall the Filter Cover
- Use your hands to align the cabin filter cover with the HVAC housing.
- Push the cover into place until both tabs click securely.
- Lightly tug the cover to confirm it is locked.
Step 8: Reattach the Glove Box
- Use your hands to lift the glove box back upward.
- Reconnect the damper arm onto the right-side pin.
- Reinstall the left and right glove box stop knobs.
- Turn the stop knobs clockwise until secure.
- No torque spec applies because these are hand-installed plastic stops.
Step 9: Check Glove Box Operation
- Use your hands to open and close the glove box several times.
- Make sure it opens smoothly and does not fall freely.
- Return your glove box items after confirming proper operation.
✅ After Repair
- Start your Tucson and turn the blower fan on.
- Test low, medium, and high fan speeds.
- Listen for rattles or fluttering, which may mean the filter cover is not clipped in fully.
- Check airflow from the vents. It should feel clean and steady.
- Replace the cabin air filter about every 12,000-15,000 miles, or sooner in dusty areas.
💰 DIY vs Shop Cost
Shop Cost: $60-$120 parts + labor
DIY Cost: $15-$35 parts only
You Save: $45-$85 by doing it yourself!
Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.2-0.4 hours.
🎯 Ready to get started?
HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.
















