🔧 TITAN - Side View Mirror Replacement

Replacing a side view mirror on your TITAN means removing the front door trim panel, unplugging the mirror connector, unbolting the mirror, and installing the new one. This is a good beginner-friendly repair if you work slowly and protect the paint and trim.

Difficulty Level: Beginner | Estimated Time: 45-90 minutes per side

---

⚠️ Safety & Precautions

• ⚠️ Disconnect the negative battery cable before unplugging mirror wiring to prevent short circuits.
• ⚠️ Wear safety glasses because door clips can pop loose suddenly.
• ⚠️ Support the mirror with one hand when removing the final nut so it does not fall and scratch the door.
• ⚠️ Do not pry on painted surfaces with metal tools; use plastic trim tools only.
• ⚠️ If your replacement mirror has heat, turn signal, puddle lamp, memory, power-fold, or camera features, the new mirror must match the old mirror’s options.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 10mm socket
• Ratchet wrench
• 6-inch socket extension
• Phillips #2 screwdriver
• Small flathead screwdriver
• Trim panel removal tool set
• Torque wrench inch-pound
• Painter’s tape
• Magnetic pickup tool
• Work light
• Safety glasses
• Mechanic gloves

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Side view mirror assembly - Qty: 1 per side
• Front door trim panel clips - Qty: 4-8 per door
• Mirror mounting nuts - Qty: 3 per side if damaged or missing

---

📋 Before You Begin

• Park your TITAN on level ground and set the parking brake.
• Fully lower the window on the side you are repairing.
• Turn the ignition OFF and remove the key from the vehicle.
• Use a 10mm socket to disconnect the negative battery cable. Wait 3 minutes before unplugging door connectors.
• Apply painter’s tape around the mirror base and upper door edge to help protect the paint.
• A door trim clip is a plastic fastener that snaps the panel to the metal door. Some clips may break during removal, so replacements are useful.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Remove the mirror inside trim cover

• Use a trim panel removal tool to gently pry off the triangular inner trim cover at the front upper corner of the door.
• Pull straight outward so the retaining clips release evenly.
• Set the trim cover aside where it will not get stepped on.
• Plastic trim cracks if twisted.

Step 2: Remove hidden screw covers

• Use a small flathead screwdriver wrapped with painter’s tape to lift the small covers in the door pull handle and interior door handle areas.
• Use the work light to check for all screws before pulling the door panel.

Step 3: Remove the front door panel screws

• Use a Phillips #2 screwdriver to remove the visible door panel screws.
• Use a 10mm socket and ratchet wrench if your door pull handle uses 10mm bolts instead of screws.
• Keep the screws and bolts organized by location.

Step 4: Release the front door trim panel clips

• Use a trim panel removal tool set at the lower edge of the door panel.
• Slide the tool close to each clip and pry straight outward until the clip pops loose.
• Work along the bottom and both sides of the panel.
• A trim panel removal tool is a plastic pry tool that removes panels without damaging the trim.

Step 5: Lift the door panel away

• Use both hands to lift the door panel upward off the window ledge.
• Hold the panel close to the door because wiring and handle cables may still be attached.
• Use a small flathead screwdriver to press connector lock tabs and unplug the door switch connectors.
• If handle cables are in the way, use the small flathead screwdriver to release each cable end from its bracket.

Step 6: Locate and unplug the mirror connector

• Use the work light to find the mirror wiring connector near the front upper inside of the door.
• Use a small flathead screwdriver to press the connector lock tab.
• Pull the connector body apart by hand. Do not pull on the wires.

Step 7: Remove the mirror mounting nuts

• Support the mirror outside the door with one hand.
• Use a 10mm socket, 6-inch socket extension, and ratchet wrench to remove the mirror mounting nuts from inside the door.
• Use a magnetic pickup tool if a nut drops inside the door.
• Remove the last nut slowly while holding the mirror steady.

Step 8: Remove the old mirror

• Pull the mirror straight away from the outside of the door by hand.
• Feed the wiring harness through the door opening carefully.
• Use the trim panel removal tool only if the mirror gasket is lightly stuck to the paint.
• Do not scrape the door with a screwdriver.

Step 9: Install the new mirror

• Feed the new mirror wiring harness through the door opening by hand.
• Place the mirror studs through the mounting holes.
• Hold the mirror flush against the door while starting all mounting nuts by hand.
• Use the 10mm socket, 6-inch socket extension, and inch-pound torque wrench to tighten the mirror nuts evenly to Torque to 7-9 Nm (62-80 in-lbs).

Step 10: Connect and test the mirror

• Plug the mirror electrical connector together by hand until it clicks.
• Use a 10mm socket to temporarily reconnect the negative battery cable.
• Turn the ignition ON and test mirror glass movement with the mirror switch.
• Test heat, turn signal, puddle lamp, blind spot indicator, or power-fold functions if equipped.
• Turn the ignition OFF after testing.

Step 11: Reinstall the door panel

• Use a small flathead screwdriver to reconnect any handle cables if they were removed.
• Reconnect the door switch connectors by hand until each one clicks.
• Hang the upper edge of the door panel over the window ledge.
• Line up the trim clips and press around the edges with your palm until they snap into place.
• Replace any broken front door trim panel clips before pressing the panel on.

Step 12: Reinstall screws and trim covers

• Use a Phillips #2 screwdriver to reinstall the door panel screws.
• Use a 10mm socket for any 10mm door pull bolts.
• Snap the screw covers back into place by hand.
• Use your hands to press the triangular mirror trim cover back onto the door until it clicks.

Step 13: Final battery connection

• Use a 10mm socket to tighten the negative battery cable securely.
• Start the vehicle and check that the door switch panel works normally.
• If the driver window auto-up function needs relearning, fully close the window and hold the switch up for 3-5 seconds.

---

✅ After Repair

• ✅ Adjust the mirror glass to your normal driving position.
• ✅ Confirm the mirror is tight and does not shake when the door closes.
• ✅ Test power adjustment, heating, signal, puddle lamp, memory, power-fold, and camera functions if equipped.
• ✅ Confirm the door locks, window switch, and speaker work after the panel is reinstalled.
• ✅ Check for wind noise on a short drive; a loose mirror gasket can cause noise.

---

💰 DIY vs Shop Cost

Shop Cost: $350-$850 per side (parts + labor)

DIY Cost: $120-$550 per side (parts only)

You Save: $230-$300 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.8-1.5 hours per side.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.