Howtoo Logo
2018 Chevrolet Silverado 1500
2014 - 2023 Chevrolet Silverado 1500
V8 5.3L
Compatible with more variants.

Here is everything needed for this repair

See what I can do

Make Money

With HowToo

OnOff
How To Replace Ignition Coils 14-19 Chevy Silverado

How To Replace Ignition Coils 14-19 Chevy Silverado

Suggested Parts

See all parts background
See All Parts

Tools & Fluids

10mm
10mm
Socket
or (3/8")
8mm
8mm
Socket
or (5/16")
3/8
3/8
Ratchet
3"
3"
Extension
Flathead
Flathead
Screwdriver
See all parts background
See All Tools

How to Replace Ignition Coils on a 2018 Chevrolet Silverado 1500

Step-by-step instructions with tools, parts, torque specs, and safety tips for 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023

How to Replace Ignition Coils on a 2018 Chevrolet Silverado 1500

Step-by-step instructions with tools, parts, torque specs, and safety tips for 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023

Orion
Orion

🔧 Ignition Coils - Replacement

Your Silverado uses individual coil-on-plug ignition coils, one on each spark plug. Replacing a bad coil can fix misfires, rough idle, hesitation, and check-engine lights tied to a specific cylinder.

Difficulty Level: Beginner | Estimated Time: 1-2 hours


⚠️ Safety & Precautions

  • Ignition coils can produce very high voltage. Do not touch the coil connector or spark plug area with the engine running.
  • Let the engine cool fully before starting. Hot intake parts and cylinder heads can cause burns.
  • Disconnect the negative battery cable before unplugging coils. This helps avoid setting extra fault codes.
  • Keep dirt out of the spark plug wells. Debris can cause misfires after the repair.
  • If you find oil in the plug wells, stop and fix the valve cover leak first.

🔧 Required Tools

You'll need the following tools for this repair:

  • 10mm socket
  • 8mm socket
  • Ratchet
  • Extension set
  • Small flat-blade screwdriver
  • Trim removal tool
  • Torque wrench capable of low inch-pound settings
  • Dielectric grease
  • Safety glasses
  • Mechanic gloves

🔩 Required Parts

HowToo sells all the parts you need for this repair:

  • Ignition coil - Qty: 1 per cylinder serviced
  • Dielectric grease - Qty: 1 tube
  • Engine cover retainer clips - Qty: as needed

📋 Before You Begin

  • Park on level ground and set the parking brake.
  • Let the engine cool completely.
  • Disconnect the negative battery cable with a 10mm socket.
  • If you are replacing a coil after a misfire, note the cylinder number from the code first so you can match the correct coil.

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Remove the engine cover

  • Use a trim removal tool or by hand, depending on the cover style, to lift the plastic engine cover off the top of the engine.
  • Set it aside in a safe place.
  • Pull straight up to avoid breaking tabs.

Step 2: Disconnect the battery

  • Use a 10mm socket to remove the negative battery cable.
  • Move the cable aside so it cannot spring back and touch the post.

Step 3: Access the ignition coil

  • Locate the coil for the cylinder you are servicing.
  • If any intake ducting blocks access, remove it using an 8mm socket and a ratchet.
  • Place all hardware in order so it goes back in the same place.

Step 4: Unplug the coil connector

  • Press the connector lock tab and unplug the electrical connector from the coil.
  • If the tab is stubborn, use a small flat-blade screwdriver very gently to help release it.
  • Do not force the connector.

Step 5: Remove the ignition coil

  • Use a 10mm socket, ratchet, and extension to remove the coil hold-down bolt.
  • Lift the coil straight up and out of the spark plug well.
  • If it sticks, twist it slightly by hand and try again.

Step 6: Inspect the coil boot and plug well

  • Check the rubber boot for tears, swelling, or oil contamination.
  • Look down into the plug well for oil, water, or debris.
  • If you see contamination, clean it out before installing the new coil.

Step 7: Install the new ignition coil

  • Apply a small amount of dielectric grease inside the coil boot.
  • Set the new coil straight into the spark plug well.
  • Install the coil bolt by hand first to avoid cross-threading.
  • Use a 10mm socket to tighten the bolt.
  • Torque to 8 Nm (71 in-lbs).

Step 8: Reconnect the electrical connector

  • Push the connector onto the coil until it clicks.
  • Give it a light tug to make sure it is locked in place.

Step 9: Reinstall removed intake parts and the engine cover

  • If you removed any intake ducting, reinstall it with an 8mm socket.
  • Reinstall the engine cover by pressing it down evenly.
  • Make sure all clips and tabs are fully seated.

Step 10: Reconnect the battery and verify repair

  • Reconnect the negative battery cable using a 10mm socket.
  • Start the engine and listen for smooth idle.
  • Check that the check-engine light is off.

✅ After Repair

  • Drive the truck and confirm the misfire is gone.
  • If the check-engine light stays on, clear codes with a scan tool and recheck.
  • If the same cylinder misfires again, inspect the spark plug and injector next.

💰 DIY vs Shop Cost

Shop Cost: $250-$800 (parts + labor)

DIY Cost: $40-$320 (parts only)

You Save: $210-$480 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 1-2 hours.


🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.

Parts
Tools
2018 Chevrolet Silverado 1500
Menu
Videos
Earn