🔧 Accord - Front Windshield Wiper Blade Replacement

Replacing the front windshield wiper blades on your Accord is a simple beginner-friendly repair. Fresh blades help prevent streaking, skipping, and poor visibility in rain.

Difficulty Level: Beginner | Estimated Time: 10-15 minutes

---

⚠️ Safety & Precautions

• ⚠️ Do not let the bare metal wiper arm snap back onto the windshield; it can crack the glass.
• ⚠️ Turn the ignition off before starting so the wipers cannot move unexpectedly.
• ⚠️ Replace both front blades together for even wiping performance.
• ⚠️ Battery disconnect is not required for this repair.

---

🔧 Required Tools

You'll need the following tools for this repair:

• Clean microfiber towel
• Safety gloves
• Safety glasses

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Front wiper blades - Driver: 26", Passenger: 16" - Qty: 2

---

📋 Before You Begin

• Park your Accord on level ground and turn the ignition fully off.
• Make sure the wiper switch is in the OFF position.
• Place a clean microfiber towel at the base of the windshield in case a wiper arm slips.
• The wiper arm is the metal piece that holds the rubber blade against the windshield.
• The connector is the small plastic latch area where the blade attaches to the arm.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Lift The Driver-Side Wiper Arm

• Use your safety gloves to gently lift the driver-side wiper arm away from the windshield.
• Raise it until it stays up on its own.
• Do not pull sideways on the arm; lift it straight away from the glass.
• Keep one hand on the arm.

Step 2: Release The Old Driver-Side Blade

• Use your fingers to press the small release tab on the wiper blade connector.
• Slide the old blade downward toward the base of the wiper arm until it comes free from the hook.
• No socket or screwdriver is needed for the factory-style hook connector.
• There is no torque specification because no bolts are removed.

Step 3: Protect The Windshield

• Use the clean microfiber towel to cushion the windshield under the raised metal arm.
• Gently lower the bare wiper arm onto the towel if you need both hands.
• Do not leave the bare arm resting directly on the glass.

Step 4: Install The New Driver-Side Blade

• Use your hands to line up the new 26" driver-side blade with the hook on the wiper arm.
• Slide the new blade upward into the hook until it clicks firmly into place.
• Gently tug the blade downward by hand to confirm it is locked.
• A clear click means it is seated.

Step 5: Lower The Driver-Side Wiper Arm

• Use both hands to carefully lower the wiper arm back onto the windshield.
• Make sure the rubber edge sits flat against the glass.

Step 6: Replace The Passenger-Side Blade

• Use your safety gloves to lift the passenger-side wiper arm away from the windshield.
• Use your fingers to press the release tab on the old blade connector.
• Slide the old blade downward and off the hook-style arm.
• Use the clean microfiber towel to protect the windshield under the bare arm.
• Use your hands to slide the new 16" passenger-side blade into the hook until it clicks.
• Gently tug the blade by hand to make sure it is locked in place.
• Carefully lower the wiper arm back onto the windshield.

Step 7: Clean And Test The Wipers

• Use the clean microfiber towel to wipe dust from the windshield where the blades travel.
• Turn the ignition to ON without starting the engine.
• Use the wiper stalk to spray washer fluid and run the wipers for a few passes.
• Check that both blades wipe smoothly without streaking, chattering, or lifting.

---

✅ After Repair

• ✅ Confirm both blades are fully locked into the wiper arms.
• ✅ Check that the driver-side 26" blade does not hit the windshield trim.
• ✅ Check that the passenger-side 16" blade clears smoothly and parks correctly.
• ✅ If streaks remain, clean the windshield again and wipe the rubber blade edges with a damp microfiber towel.

---

💰 DIY vs Shop Cost

Shop Cost: $45-$85 (parts + labor)

DIY Cost: $20-$45 (parts only)

You Save: $25-$40 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.2-0.3 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.