How to Replace Front Windshield Wipers on a 2017-2026 Hyundai Tucson
Step-by-step wiper blade installation guide with blade sizes, tools, and safety tips for 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025, 2026
How to Replace Front Windshield Wipers on a 2017-2026 Hyundai Tucson
Step-by-step wiper blade installation guide with blade sizes, tools, and safety tips for 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025, 2026
🔧 Tucson - Front Windshield Wiper Blade Replacement
Replacing the front windshield wiper blades is a quick beginner-friendly repair. Fresh blades help your Tucson clear rain safely and prevent streaking, skipping, or scratching the windshield.
Difficulty Level: Beginner | Estimated Time: 10-15 minutes
⚠️ Safety & Precautions
- ⚠️ Do not let the bare metal wiper arm snap back onto the windshield; it can crack the glass.
- ⚠️ Work with the ignition off and the wipers parked at the bottom of the windshield.
- ⚠️ If the windshield is hot, let it cool before lifting the wiper arms.
🔧 Required Tools
You'll need the following tools for this repair:
- Safety glasses
- Microfiber towel
🔩 Required Parts
HowToo sells all the parts you need for this repair:
- Front wiper blades - Driver: 26", Passenger: 16" - Qty: 2
📋 Before You Begin
- 🅿️ Park your Tucson on level ground and turn the ignition off.
- 🧼 Clean the lower windshield area with a microfiber towel so dirt does not scratch the glass.
- 🧤 Keep the new wiper blades in their packaging until you are ready to install each one.
- 💡 A wiper arm is the spring-loaded metal arm that holds the rubber blade against the windshield.
🔨 Step-by-Step Instructions
Follow these steps in order:
Step 1: Lift the Driver-Side Wiper Arm
- Put on safety glasses.
- Gently lift the driver-side wiper arm away from the windshield until it stays upright.
- Place a microfiber towel on the windshield under the raised arm.
- Protect the glass before removing the blade.
Step 2: Release the Old Driver-Side Blade
- Find the small locking tab where the blade connects to the wiper arm.
- Use your thumb to press the locking tab.
- Slide the old blade downward toward the base of the wiper arm until it unlocks from the hook.
- A hook-style arm is a curved end shaped like a “J” that holds the blade in place.
Step 3: Remove the Old Driver-Side Blade
- Pull the old blade fully off the wiper arm by hand.
- Keep one hand on the metal wiper arm so it cannot spring back onto the windshield.
- Do not leave the bare arm standing without holding it or resting it carefully on the towel.
Step 4: Install the New Driver-Side Blade
- Remove the new 26" driver-side wiper blade from its package.
- Slide the new blade adapter into the hook of the wiper arm by hand.
- Pull the blade upward into the hook until you hear or feel a click.
- Gently tug the blade downward to confirm it is locked.
- No fasteners are used, so there is no torque spec for this repair.
Step 5: Lower the Driver-Side Wiper Arm
- Hold the wiper arm firmly with one hand.
- Remove the microfiber towel.
- Slowly lower the new blade onto the windshield.
- Never drop the arm onto the glass.
Step 6: Replace the Passenger-Side Blade
- Lift the passenger-side wiper arm away from the windshield.
- Place the microfiber towel under the arm.
- Press the blade’s locking tab by hand.
- Slide the old blade off the hook-style arm.
- Install the new 16" passenger-side wiper blade by sliding it into the hook until it clicks.
- Gently tug the blade to confirm it is locked.
- Slowly lower the wiper arm back onto the windshield.
Step 7: Check Blade Position
- Look at both blades and make sure the rubber edge sits flat against the windshield.
- Make sure each blade is centered on its wiper arm and not twisted.
- Use the microfiber towel to wipe the rubber edge once before testing.
✅ After Repair
- 💧 Spray windshield washer fluid and run the wipers for 5-10 seconds.
- 👀 Check for streaks, chatter, skipping, or loose movement.
- 🔒 If a blade moves loosely, turn the wipers off and re-seat the blade until it clicks.
- 🧼 Clean the windshield if streaks remain after installation.
💰 DIY vs Shop Cost
Shop Cost: $45-$90 (parts + labor)
DIY Cost: $20-$45 (parts only)
You Save: $25-$45 by doing it yourself!
Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.1-0.2 hours.
🎯 Ready to get started?
HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.








