🔧 F-150 - Front Windshield Wiper Blade Replacement

Replacing the front windshield wiper blades on your F-150 is a quick beginner-friendly job. The old blades release from the wiper arms, and the new blades lock into place so they can clear rain, dust, and road film properly.

Difficulty Level: Beginner | Estimated Time: 10-20 minutes

---

⚠️ Safety & Precautions

• ⚠️ Turn the ignition off before working near the wiper arms.
• ⚠️ Do not let a bare metal wiper arm snap back onto the windshield. It can crack the glass.
• ⚠️ Keep fingers clear of the wiper arm hinge. It is spring-loaded.
• ⚠️ Battery disconnect is not required for this repair.

---

🔧 Required Tools

You'll need the following tools for this repair:

• Nitrile gloves
• Safety glasses
• Shop towel

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Front wiper blades - Driver: 22", Passenger: 22" - Qty: 2

---

📋 Before You Begin

• 🅿️ Park your F-150 on level ground and turn the ignition off.
• 🧼 Clean the lower windshield area with a shop towel so grit does not scratch the glass.
• 🧤 Put on nitrile gloves for better grip and cleaner handling.
• 📌 Your F-150 uses hook-style front wiper arms. A hook-style arm has a curved J-shaped end that the blade slides into and locks onto.
• 📦 Replace both front wiper blades together for even wiping performance.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Lift the Driver-Side Wiper Arm

• Use your hand while wearing nitrile gloves to lift the driver-side wiper arm away from the windshield.
• Place a folded shop towel on the windshield under the wiper arm as a cushion.
• Hold the arm firmly. It is spring-loaded and can snap down.

Step 2: Rotate the Old Blade

• Use your hand to rotate the old wiper blade so it sits nearly perpendicular to the wiper arm.
• Look for the small locking tab where the blade connects to the J-hook end.
• A locking tab is the small plastic latch that keeps the blade from sliding off the arm.

Step 3: Release the Old Blade

• Use your thumb to press the locking tab on the wiper blade adapter.
• While holding the tab, slide the blade downward toward the base of the wiper arm.
• Once it clears the hook, remove the old blade by hand.
• Keep one hand on the arm.

Step 4: Protect the Windshield

• Use your hand to gently lower the bare wiper arm onto the folded shop towel.
• Do not leave the bare metal arm standing upright unattended.

Step 5: Install the New Driver-Side Blade

• Use your hand to position the new 22-inch wiper blade with the adapter opening facing the J-hook.
• Slide the blade up into the hook until you hear or feel a click.
• Pull gently on the blade by hand to confirm it is locked.
• No fasteners are used, so there is no torque spec for this repair.

Step 6: Lower the Driver-Side Wiper Arm

• Use your hand to lift the wiper arm slightly off the shop towel.
• Remove the shop towel from the windshield.
• Slowly lower the new blade onto the glass.

Step 7: Repeat on the Passenger Side

• Use your hand while wearing nitrile gloves to lift the passenger-side wiper arm away from the windshield.
• Place the folded shop towel under the arm on the windshield.
• Use your thumb to press the locking tab on the old blade.
• Slide the old blade downward out of the J-hook and remove it by hand.
• Use your hand to slide the new 22-inch wiper blade into the hook until it clicks.
• Pull gently on the blade by hand to confirm it is locked.
• Remove the shop towel and slowly lower the blade onto the windshield.

Step 8: Test the New Wipers

• Use the windshield washer switch inside the cab to spray washer fluid onto the windshield.
• Run the wipers for several swipes.
• Watch for streaking, skipping, chatter, or a blade that is not seated correctly.

---

✅ After Repair

• ✅ Confirm both blades sit flat against the windshield.
• ✅ Make sure each blade is locked into its J-hook by gently pulling on it.
• ✅ If streaks remain, clean the windshield with glass cleaner and a shop towel.
• ✅ Replace wipers about every 6-12 months, sooner in heavy heat, dust, or monsoon conditions.

---

💰 DIY vs Shop Cost

Shop Cost: $45-$90 (parts + labor)

DIY Cost: $18-$45 (parts only)

You Save: $25-$55 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.2-0.4 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.