How to Replace Front Windshield Wipers on a 2011-2025 Ram 1500 (Trim: Laramie)
Step-by-step guide with 24-inch blade sizes, tools, safety tips, and testing for 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025
How to Replace Front Windshield Wipers on a 2011-2025 Ram 1500 (Trim: Laramie)
Step-by-step guide with 24-inch blade sizes, tools, safety tips, and testing for 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025
🔧 1500 - Front Windshield Wiper Blade Replacement
Replacing the front windshield wiper blades on your 1500 is a quick beginner repair. Fresh blades improve visibility and prevent streaking, chatter, and windshield scratches from worn rubber.
Difficulty Level: Beginner | Estimated Time: 10-15 minutes
⚠️ Safety & Precautions
- ⚠️ Do not let the bare metal wiper arm snap back onto the windshield. It can crack the glass.
- ⚠️ Turn the ignition off before working near the wipers so they cannot move unexpectedly.
- ⚠️ Use a towel or folded cloth on the glass while each blade is removed for protection.
- ⚠️ Battery disconnect is not required for this repair.
🔧 Required Tools
You'll need the following tools for this repair:
- Safety glasses
- Nitrile gloves
- Microfiber towel
- Small flat-blade screwdriver
🔩 Required Parts
HowToo sells all the parts you need for this repair:
- Front wiper blades - Driver: 24", Passenger: 24" - Qty: 2
📋 Before You Begin
- Park your 1500 on level ground and turn the ignition off.
- Make sure the wiper switch is in the OFF position.
- Place a microfiber towel on the windshield under the wiper arm you are working on.
- A flat-blade screwdriver is a simple prying tool with a flat tip. Use it gently so you do not damage the plastic clip.
🔨 Step-by-Step Instructions
Follow these steps in order:
Step 1: Lift The Driver Wiper Arm
- Use your hands to lift the driver-side wiper arm away from the windshield until it stays raised.
- Place the microfiber towel between the arm area and the windshield for glass protection.
- Keep one hand on the arm.
Step 2: Find The Release Tab
- Look where the blade connects to the wiper arm. Your 1500 uses a hook-style wiper arm connection.
- The hook-style connector is a curved metal arm end that locks into the plastic adapter on the blade.
- Use your fingers to feel for the small release tab on the blade adapter.
Step 3: Unlock The Old Wiper Blade
- Press the release tab with your thumb.
- If the tab is stiff, use a small flat-blade screwdriver to gently press the tab.
- Do not pry hard. The plastic connector can break.
Step 4: Slide The Old Blade Off
- While holding the tab open, use your hand to slide the wiper blade down toward the base of the wiper arm.
- The blade will move out of the hook and come free.
- Slowly lower the bare wiper arm onto the microfiber towel, not directly onto the glass.
Step 5: Install The New Driver Wiper Blade
- Pick up one new 24-inch front wiper blade.
- Use your hands to slide the blade adapter into the hook end of the wiper arm.
- Pull the blade upward into the hook until it clicks.
- A click means it is locked.
Step 6: Check The Driver Blade Lock
- Use your hand to gently tug the blade downward.
- If it slides off, reinstall it until the connector fully clicks into place.
- Carefully lower the wiper arm back onto the windshield.
Step 7: Replace The Passenger Wiper Blade
- Repeat the same process on the passenger side using the second 24-inch front wiper blade.
- Use the microfiber towel under the passenger wiper arm while the blade is removed.
- Use the small flat-blade screwdriver only if the release tab is hard to press by hand.
Step 8: Clean The Windshield
- Use the microfiber towel to wipe the lower windshield area where dirt collects.
- Remove any packaging covers from the new wiper rubber before testing.
- No torque specs apply to this repair because no bolts or nuts are removed.
✅ After Repair
- ✅ Turn the ignition on and spray washer fluid onto the windshield.
- ✅ Run the wipers on low speed and confirm both blades wipe smoothly.
- ✅ Check for streaking, skipping, or noise.
- ✅ If a blade chatters, clean the windshield again and confirm the blade is fully locked into the arm.
💰 DIY vs Shop Cost
Shop Cost: $45-$90 (parts + labor)
DIY Cost: $25-$45 (parts only)
You Save: $20-$45 by doing it yourself!
Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.2-0.3 hours.
🎯 Ready to get started?
HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.










