🔧 CX-5 - Front Windshield Wiper Blade Replacement

Your CX-5 uses two different front blade sizes: 24 inches on the driver side and 18 inches on the passenger side. Replacing the complete blades is easier than transferring rubber refills and requires no vehicle disassembly.

Difficulty Level: Beginner | Estimated Time: 10-15 minutes

---

⚠️ Safety & Precautions

• ⚠️ Switch the ignition off and leave the wiper control in the OFF position.
• ⚠️ Raise the driver-side arm first; when finished, lower the passenger-side arm first.
• ⚠️ Never release a raised wiper arm against the glass. The bare metal arm can crack the windshield.
• ⚠️ Do not manually sweep the arms sideways across the windshield.
• ⚠️ Battery disconnection is not required.

Mazda specifically warns against letting an arm snap onto the windshield and specifies the lifting and lowering order above. mazdausa.com)

---

🔧 Required Tools

You'll need the following tools for this repair:

• Windshield cleaning cloth
• Safety glasses
• Work gloves

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• 24-inch front driver-side wiper blade - Qty: 1
• 18-inch front passenger-side wiper blade - Qty: 1

Replace in pairs so both sides provide consistent visibility. The matching wiper aisle is open in the parts sidebar.

---

📋 Before You Begin

• 📍 Park your CX-5 on level ground and switch the ignition completely off.
• 📍 Confirm that the replacement package lists the correct side and includes the Mazda-compatible push-button connector.
• 📍 Place a folded windshield cleaning cloth on the glass beneath each blade as extra protection.
• 📍 No infotainment setting, scan tool, service mode, or battery disconnect is required for this procedure.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Raise the driver-side wiper arm

• Use your work gloves to grasp the driver-side arm near the blade.
• Lift the arm away from the windshield until it remains raised.
• Keep control of the arm and do not pull it sideways.

Step 2: Remove the driver-side blade

• Locate the small release tab where the blade connects to the arm.
• Press the release tab with your thumb while sliding the blade along the arm and away from its locked position.
• Remove the blade carefully. A release tab is the small plastic button that unlocks the connector.
• Slowly rest the protected arm against the folded windshield cleaning cloth if necessary.

Step 3: Install the new driver-side blade

• Orient the 24-inch driver-side blade so its connector grooves align with the tabs on the wiper arm.
• Slide the blade onto the arm until the connector locks firmly.
• Gently pull the blade without pressing the release tab. It should remain attached.
• Listen and feel for the locking click.

Step 4: Raise and remove the passenger-side blade

• Use your work gloves to raise the passenger-side arm.
• Press its connector release tab and slide the old blade off the arm.
• Keep one hand on the arm so it cannot spring against the glass.

Step 5: Install the new passenger-side blade

• Align the 18-inch passenger-side blade with the arm connector.
• Slide it into place until it locks.
• Gently pull the blade to verify that the connector is secure.

Step 6: Lower the wiper arms correctly

• Use both hands to lower the passenger-side arm first.
• Slowly lower the driver-side arm second.
• Confirm that both rubber edges sit flat against the windshield.

Step 7: Alternative for Mazda rubber refills

• If you purchased rubber refills rather than complete blades, press the arm tab and remove the original blade assembly.
• Slide the rubber until the blade-holder groove becomes visible, release its end from the groove, and pull the rubber out.
• Transfer the metal stiffeners only if the refill instructions require it, keeping their original orientation.
• Feed the new rubber through every holder and seat its end securely in the retaining groove.
• Mazda cautions against bending the rubber or metal stiffeners during this operation. mazdausa.com

---

✅ After Repair

• ✅ Remove the protective cloth and clear all tools from the windshield area.
• ✅ Switch the ignition on and spray windshield-washer fluid.
• ✅ Run the wipers at low speed and check for streaking, chatter, loose connectors, or contact between the blades.
• ✅ If streaking remains, clean the windshield and rubber edges with mild detergent and rinse with clean water, as Mazda recommends. mazdausa.com
• ✅ Stop immediately if a blade shifts or separates from its arm.

---

💰 DIY vs Shop Cost

Shop Cost: ₹2,500-₹5,000 equivalent, including blades and installation

DIY Cost: ₹1,200-₹4,000 equivalent, parts only

You Save: Approximately ₹500-₹1,500 by doing it yourself!

Local parts pricing varies. Installation generally takes a shop about 0.1-0.2 hour.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.