How to Replace Front Windshield Wiper Blades on a 2005-2015 Hyundai Tucson
Step-by-step DIY instructions with blade sizes, installation tips, and safety precautions for 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
How to Replace Front Windshield Wiper Blades on a 2005-2015 Hyundai Tucson
Step-by-step DIY instructions with blade sizes, installation tips, and safety precautions for 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
🔧 Tucson - Front Windshield Wiper Blade Replacement
Replacing both front wiper blades restores clear, streak-free wiping and helps prevent windshield scratches. Your Tucson uses hook-style wiper arms, so no mechanical tools are normally required.
Difficulty Level: Beginner | Estimated Time: 10-15 minutes
⚠️ Safety & Precautions
- ⚠️ Turn the ignition off before raising the wiper arms.
- ⚠️ Do not let a bare metal wiper arm snap against the windshield.
- ⚠️ Replace one blade at a time so the blades do not get switched.
- ⚠️ Battery disconnection is not required.
🔧 Required Tools
You'll need the following tools for this repair:
- Safety glasses
- Work gloves
- Thick microfiber towel
🔩 Required Parts
HowToo sells all the parts you need for this repair:
- 24-inch driver-side front wiper blade - Qty: 1
- 18-inch passenger-side front wiper blade - Qty: 1
📋 Before You Begin
- Park your Tucson on level ground and switch off the ignition.
- Make sure the replacement blades include adapters for standard hook-style arms.
- Clean loose dirt from the lower windshield with a thick microfiber towel.
- Wiper service mode, battery disconnection, and scan-tool programming are not required.
🔨 Step-by-Step Instructions
Follow these steps in order:
Step 1: Protect the Windshield
- Put on the safety glasses and work gloves.
- Use the thick microfiber towel to cover the windshield beneath the driver-side blade.
- This protects the glass if the spring-loaded metal arm accidentally drops.
Step 2: Raise the Driver-Side Wiper Arm
- Use your gloved hand to lift the driver-side wiper arm away from the windshield.
- Stop when the arm remains raised without being forced.
- Keep one hand controlling the arm.
Step 3: Remove the Driver-Side Blade
- Rotate the blade until it sits roughly perpendicular to the wiper arm.
- Find the small locking tab where the curved hook passes through the blade adapter. The adapter is the plastic connector joining the blade to the arm.
- Use your gloved thumb to press the locking tab.
- While holding the tab, slide the blade downward toward the base of the arm.
- Move the blade around the open end of the hook and remove it.
- Gently lower the bare arm onto the thick microfiber towel.
Step 4: Install the 24-Inch Driver-Side Blade
- Use your gloved hand to lift and control the driver-side arm.
- Pass the arm's hook through the opening in the new 24-inch blade adapter.
- Pull the blade upward into the hook until the locking tab clicks.
- Gently tug the blade to verify that it is locked.
- Rotate the blade into its normal position and carefully lower it onto the glass.
Step 5: Replace the Passenger-Side Blade
- Move the thick microfiber towel beneath the passenger-side blade.
- Use your gloved hand to raise the passenger-side arm.
- Press the adapter's locking tab and slide the old blade toward the base of the arm.
- Remove the old blade from the hook while keeping control of the arm.
- Insert the hook through the new 18-inch blade adapter and pull until it clicks securely.
- Gently tug the blade, then carefully lower the arm onto the windshield.
Step 6: Check the Installation
- Use your gloved hands to confirm both blades sit flat against the windshield.
- Check that the 24-inch blade is on the driver side and the 18-inch blade is on the passenger side.
- Remove the thick microfiber towel before operating the wipers.
✅ After Repair
- ✅ Apply windshield washer fluid and operate the wipers at low speed.
- Confirm both blades move freely without touching each other or the windshield trim.
- Check for skipping, streaking, or loose adapters.
- If a blade shifts or clicks, switch off the ignition and reseat its adapter before driving.
💰 DIY vs Shop Cost
Shop Cost: ₹1,500-₹4,000 (parts + labor)
DIY Cost: ₹800-₹2,500 (parts only)
You Save: ₹700-₹1,500 by doing it yourself!
Local labor rates vary. This repair takes a shop approximately 0.1-0.3 hours.
🎯 Ready to get started?
HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.









