🔧 Side View Mirrors - Mirror Assembly Replacement

This job replaces the complete side mirror assembly on your Sierra. On this truck, the mirror is held on from inside the door, so you remove the interior sail panel, unplug the mirror connector, and swap the assembly.

Difficulty Level: Beginner | Estimated Time: 1-2 hours

---

⚠️ Safety & Precautions

• Work with the window fully up so the glass and trim are out of the way.
• Use care around the door trim clips; they can break if pulled hard.
• If the mirror has power, heat, or turn-signal wiring, unplug the connector before removal.
• No battery disconnect is usually required for this repair.
• Support the mirror while removing the last nut.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 7mm socket
• 10mm socket
• Ratchet
• Extension
• Trim panel removal tool
• Small flat-blade screwdriver
• Torque wrench
• Safety glasses
• Mechanic gloves

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Side mirror assembly - Qty: 1
• Mirror mounting nuts - Qty: 3
• Door trim clip set - Qty: 1

---

📋 Before You Begin

• Park on level ground and set the parking brake.
• Roll the window fully up.
• Fold the mirror inward, if it still moves, for easier access.
• Have a towel ready to protect the door paint and trim.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Remove the interior mirror trim

• Use a trim panel removal tool to carefully pop off the triangular sail panel at the front upper corner of the door.
• If your Sierra has a small speaker or tweeter in that panel, unplug it gently.
• Pull straight out to avoid breaking clips.

Step 2: Disconnect the mirror wiring

• Reach behind the panel and locate the mirror electrical connector.
• Press the locking tab and unplug it by hand.
• If the connector is tight, use a small flat-blade screwdriver to lift the tab carefully.

Step 3: Remove the mirror mounting nuts

• Use a 10mm socket, ratchet, and extension to remove the three mirror nuts.
• Hold the mirror from the outside while removing the last nut so it does not fall.
• Torque on installation: 10 Nm (89 in-lbs)

Step 4: Remove the mirror assembly

• Lift the mirror assembly away from the door.
• Guide the wiring harness through the opening as you remove it.
• Check the foam seal before reinstalling.

Step 5: Install the new mirror assembly

• Feed the wiring through the door opening and position the new mirror on the door.
• Install the three mounting nuts by hand first.
• Use the 10mm socket and torque wrench to tighten to 10 Nm (89 in-lbs).

Step 6: Reconnect and reassemble the trim

• Reconnect the mirror electrical connector until it clicks.
• Reinstall the sail panel by lining up the clips and pressing it firmly into place.
• If any trim clips broke, replace them with the door trim clip set.

Step 7: Test the mirror

• Turn the ignition on and test mirror adjustment, heat, and turn signal if equipped.
• Make sure the mirror is secure and does not move at the base.

---

✅ After Repair

• Check mirror movement left, right, up, and down.
• If heated, verify the glass warms up after a few minutes.
• If equipped, verify the turn signal and blind-spot indicator work.
• Listen for wind noise on the test drive; a loose seal can cause whistling.

---

💰 DIY vs Shop Cost

Shop Cost: ₹7,000-₹18,000 (parts + labor)

DIY Cost: ₹3,500-₹10,000 (parts only)

You Save: ₹3,500-₹8,000 by doing it yourself!

Shop labor rates vary but typically run ₹8,000-₹12,000/hour. This repair takes a shop approximately 1-2 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.