🔧 Power Steering Pump - Replacement

The power steering pump on your Accord drives hydraulic pressure to assist steering. If it is whining, leaking, or causing heavy steering, replacement is the fix. This job requires belt removal, hose transfer, and a careful bleed afterward so the steering is quiet and smooth.

Difficulty Level: Intermediate | Estimated Time: 2-4 hours

---

⚠️ Safety & Precautions

• Work with the engine completely cool before touching the pump, belt, or fluid lines.
• Keep hands, hair, and clothing away from the serpentine belt area.
• Use jack stands if you raise the vehicle; never rely on a jack alone.
• Power steering fluid can damage paint. Wipe spills immediately.
• Battery disconnect is not required for this repair.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 10mm socket
• 12mm socket
• 14mm socket
• Ratchet
• Breaker bar
• Torque wrench
• Serpentine belt tool or 14mm wrench
• Drain pan
• Funnel
• Shop towels
• Gloves
• Safety glasses
• Jack and jack stands

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Power steering pump - Qty: 1
• Power steering fluid - Qty: 1-2 bottles
• Power steering O-ring/seal kit - Qty: 1
• Serpentine belt - Qty: 1

---

📋 Before You Begin

• Park on level ground and set the parking brake.
• Let the engine cool fully.
• Have the new pump and new seals ready before opening the system.
• Keep everything clean.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Remove the drive belt

• Use the serpentine belt tool or 14mm wrench to relieve tension from the belt tensioner.
• Slip the belt off the power steering pump pulley.
• Remove the belt from the engine bay.

Step 2: Drain the power steering fluid

• Place a drain pan under the pump and hose connections.
• Use a 12mm socket or 14mm socket as needed to remove the return hose clamp or bracket fasteners.
• Disconnect the return hose and let the fluid drain fully.
• Keep the hose end upright.

Step 3: Remove the pressure and return lines

• Use a 12mm socket to remove the pressure line fitting if equipped with a retaining bolt.
• Remove the return hose from the pump inlet.
• Catch any remaining fluid with shop towels and the drain pan.

Step 4: Remove the pump

• Use a 12mm socket and 14mm socket to remove the pump mounting bolts.
• Support the pump with one hand while removing the last bolt.
• Lift the pump out of the engine bay.

Step 5: Transfer brackets and seals

• Compare the old pump and new pump before installation.
• Use the 12mm socket to transfer any mounting bracket or brace.
• Install new power steering O-rings/seals on the line connections.
• Lube new seals with fresh fluid.

Step 6: Install the new pump

• Set the new pump into position.
• Start all mounting bolts by hand first.
• Use the torque wrench to tighten the pump mounting bolts to 27 Nm (20 ft-lbs).
• Tighten line fittings to 27 Nm (20 ft-lbs) unless the new pump instructions specify otherwise.

Step 7: Reconnect hoses and reinstall the belt

• Reconnect the pressure line and return hose.
• Use the serpentine belt tool or 14mm wrench to route the belt back over the pulleys.
• Make sure the belt is seated fully in every pulley groove.

Step 8: Refill and bleed the system

• Use a funnel to fill the reservoir with the correct power steering fluid.
• With the engine off, turn the steering wheel slowly from lock to lock 10-15 times.
• Check the fluid level and top off as needed.
• Start the engine and turn the wheel slowly again.
• Watch for bubbles, noise, or leaks.

---

✅ After Repair

• Check all hose connections for leaks with the engine running.
• Listen for whining or groaning from the pump.
• Recheck belt tracking and tension after the test drive.
• Top off fluid again after the vehicle cools.

---

💰 DIY vs Shop Cost

Shop Cost: $650-$1,100 (parts + labor)

DIY Cost: $180-$420 (parts only)

You Save: $470-$680 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 2-4 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.