How to Replace the Outer Tie Rod End on a 2016 Volkswagen GTI
Step-by-step instructions with tools, torque specs, alignment tips, and safety precautions for 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023
How to Replace the Outer Tie Rod End on a 2016 Volkswagen GTI
Step-by-step instructions with tools, torque specs, alignment tips, and safety precautions for 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023
🔧 Tie Rod End - Replacement
The outer tie rod end connects the steering rack to the front wheel. Replacing it is straightforward, but the toe angle will change, so a professional alignment is required afterward. This guide covers one side; if both ends are worn, replace both sides and then align the car.
Difficulty Level: Intermediate | Estimated Time: 1.5-2.5 hours
⚠️ Safety & Precautions
- Park on level ground and chock the rear wheels.
- Use jack stands; do not rely on the jack alone.
- Keep hands clear when separating the tie rod end from the steering knuckle.
- Do not turn the steering wheel with the tie rod end disconnected.
- An alignment is required after this repair.
🔧 Required Tools
You'll need the following tools for this repair:
- Floor jack (rated 3-ton minimum)
- Jack stands (rated for vehicle weight)
- Wheel chocks
- Safety glasses
- Mechanic gloves
- 19mm socket
- 18mm wrench
- 21mm socket
- Torque wrench
- Tie rod end puller (specialty)
- Side cutter
- Paint marker
- Penetrating oil
🔩 Required Parts
HowToo sells all the parts you need for this repair:
- Outer tie rod end - Qty: 1
- Outer tie rod end self-locking nut - Qty: 1
- Outer tie rod end jam nut - Qty: 1
- Alignment mark paint - Qty: 1
📋 Before You Begin
- Park the GTI on level ground.
- Set the parking brake.
- Loosen the front wheel lug bolts slightly before lifting.
- Spray penetrating oil on the jam nut and tie rod end threads.
- Count or measure the exposed threads before removal so the new part starts close to the same position.
🔨 Step-by-Step Instructions
Follow these steps in order:
Step 1: Raise and secure the front of the car
- Use a floor jack to lift the front of the GTI.
- Support it with jack stands under the proper front lift points.
- Remove the front wheel with a 19mm socket.
Step 2: Mark the tie rod position
- Use a paint marker to mark the jam nut position on the inner tie rod.
- Measure or count the exposed threads on the old tie rod end.
- Close enough helps with getting to the alignment shop.
Step 3: Loosen the jam nut
- Use an 18mm wrench to loosen the jam nut on the inner tie rod.
- Do not remove it yet.
Step 4: Disconnect the tie rod end from the knuckle
- Remove the self-locking nut using a 21mm socket.
- If the stud spins, hold it with an 18mm wrench while loosening the nut.
- Use a tie rod end puller (specialty) to separate the tie rod end from the steering knuckle.
- Do not hammer on the steering knuckle.
Step 5: Remove the old tie rod end
- Count the turns as you unscrew the old tie rod end from the inner tie rod.
- Use an 18mm wrench on the jam nut if needed while turning the tie rod end by hand.
- Remove the old tie rod end.
Step 6: Install the new tie rod end
- Thread the new tie rod end on the same number of turns as the old one.
- Install the outer end into the steering knuckle.
- Install the new self-locking nut by hand first.
Step 7: Tighten the hardware
- Use a 21mm socket and 18mm wrench to tighten the tie rod end nut.
- Torque the tie rod end nut to 45 Nm (33 ft-lbs) plus 90°.
- Use an 18mm wrench to tighten the jam nut.
- Torque the jam nut to 50 Nm (37 ft-lbs).
Step 8: Reinstall the wheel and lower the car
- Reinstall the wheel with a 19mm socket.
- Lower the GTI to the ground.
- Torque the wheel bolts to 120 Nm (89 ft-lbs).
✅ After Repair
- Start the car and turn the steering wheel lock-to-lock to check for any binding.
- Drive slowly at first and listen for clunks or rubbing.
- Schedule a front-end alignment as soon as possible.
- If the steering wheel is off-center after the alignment, the shop should correct it.
💰 DIY vs Shop Cost
Shop Cost: $180-$350 (parts + labor)
DIY Cost: $35-$85 (parts only)
You Save: $145-$265 by doing it yourself!
Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 1-2 hours.
🎯 Ready to get started?
HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.


















