How to Replace the Fuel Pump Module on a 2005-2013 Nissan Frontier (In-Tank Pump) (Engine: V6 4.0L)
Step-by-step access-panel vs tank-drop methods, required tools/parts, safety tips, and leak checks
How to Replace the Fuel Pump Module on a 2005-2013 Nissan Frontier (In-Tank Pump) (Engine: V6 4.0L)
Step-by-step access-panel vs tank-drop methods, required tools/parts, safety tips, and leak checks for 2005, 2006, 2007, 2008, 2009, 2010, 2013
🔧 Frontier - Fuel Pump Replacement
On your Frontier, the fuel pump is part of the in-tank fuel pump module (pump + level sender + strainer). Replacement is usually done through a service access panel under the rear seat (Crew Cab), but some trucks require lowering the fuel tank.
Difficulty Level: Intermediate | Estimated Time: 2-5 hours
⚠️ Safety & Precautions
- ⚠️ Gasoline fumes are flammable—work outdoors or in a well-ventilated area.
- ⚠️ No sparks/flames: no smoking, no drop lights with hot bulbs.
- ⚠️ Relieve fuel pressure before disconnecting fuel lines.
- ⚠️ Disconnect the negative battery cable before opening the tank/module.
- ⚠️ Keep a Class B fire extinguisher nearby.
🔧 Required Tools
You'll need the following tools for this repair:
- 10mm socket
- 12mm socket
- 3/8" drive ratchet
- 3/8" drive torque wrench (10–100 ft-lbs)
- Phillips #2 screwdriver
- Trim clip removal tool
- Needle-nose pliers
- Fuel line disconnect tool set (specialty)
- Brass drift and hammer (specialty)
- Shop towels
- Drain pan
- Nitrile gloves
- Safety glasses
- Floor jack (rated 3-ton minimum)
- Jack stands (rated 3-ton minimum)
- Wheel chocks
🔩 Required Parts
HowToo sells all the parts you need for this repair:
- Fuel pump module assembly - Qty: 1
- Fuel pump module seal O-ring - Qty: 1
- Fuel pump strainer sock - Qty: 1
📋 Before You Begin
- Park on level ground and set the parking brake.
- Chock the front wheels using wheel chocks.
- Get the fuel level as low as possible (under 1/4 tank is best).
- Plan to replace the seal O-ring no matter what.
🔨 Step-by-Step Instructions
Before I give you the exact steps for your Frontier, I need 2 quick checks so I don’t send you down the wrong method:
- Does your Frontier have a fuel pump access cover under the rear seat (a metal plate you can unbolt)?
- Are you replacing the whole fuel pump module assembly, or only the pump motor inside the module?
Reply with those two answers and I’ll lay out the correct step-by-step procedure (access-cover method vs tank-drop method), including the right tightening specs and reassembly checks.
✅ After Repair
- Cycle the key ON for 3 seconds, OFF for 10 seconds, repeat 3 times to prime the system.
- Start the engine and check carefully for fuel leaks at the line connections and module seal area.
💰 DIY vs Shop Cost
Shop Cost: $650-$1,200 (parts + labor)
DIY Cost: $250-$700 (parts only)
You Save: $400-$500+ by doing it yourself!
Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 2-4 hours.
🎯 Ready to get started?
HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.
