🔧 Town & Country - Engine Air Filter Replacement

Replacing the engine air filter helps your A4 breathe clean air, which supports smooth power and good fuel economy. On your Town & Country, the filter sits inside the air cleaner box in the engine bay and is designed to be a quick DIY service.

Difficulty Level: Beginner | Estimated Time: 0.2-0.5 hours

Assumption: stock (factory) air intake/air box.

---

⚠️ Safety & Precautions

• 🧯 Work on a cool engine to avoid burns.
• 🧤 Keep fingers clear of the radiator fan area; it can turn on unexpectedly.
• 🛑 Do not run the engine with the air filter removed.
• 🔌 Battery disconnect is not required for this job.

---

🔧 Required Tools

You'll need the following tools for this repair:

• Safety glasses
• Nitrile gloves
• Flashlight
• Clean shop towels
• Trim clip tool
• Flathead screwdriver

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Engine air filter - Qty: 1

---

📋 Before You Begin

• 🅿️ Park on level ground, shift to Park, and set the parking brake.
• 🧊 Let the engine cool for 15–30 minutes if it was just running.
• 🧼 Have a clean towel ready so dirt doesn’t fall into the air box.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Open the hood and locate the air cleaner box

• Open the hood and support it securely.
• Use a flashlight to find the air cleaner box (the plastic box connected to the large intake tube).

Step 2: Unclip the air cleaner box cover

• Locate the metal retaining clips around the air box seam.
• Release the clips by hand; if a clip is stubborn, gently help it with a flathead screwdriver.
• Don’t pry hard—plastic tabs can crack.

Step 3: Lift the cover and remove the old filter

• Lift the top half of the air box enough to access the filter.
• Pull the old filter straight out.
• Use a flashlight to check the bottom half of the box for leaves or dirt.

Step 4: Clean the air box sealing surface

• Wipe out loose debris with clean shop towels.
• If a small plastic push-clip or wire is in your way, use a trim clip tool carefully to move it without breaking it (a trim clip tool is a small pry tool made to pop plastic clips without damage).
• Do not let dirt fall into the intake tube.

Step 5: Install the new air filter

• Place the new filter into the lower air box the same way the old one came out.
• Make sure the rubber seal sits flat all the way around (no pinches or gaps).

Step 6: Close the air box and latch the clips

• Lower the air box cover back into position, lining up the edges.
• Snap all the retaining clips closed by hand.
• If you loosened anything, snug it carefully with a flathead screwdriver (no torque spec required for this step).

---

✅ After Repair

• 🔎 Double-check every clip is fully latched and the cover sits evenly.
• 🚗 Start the engine and let it idle for 30 seconds; listen for any hissing (a sign the air box isn’t sealed).
• 🧾 Note the mileage/date for your maintenance records.

---

💰 DIY vs Shop Cost

Shop Cost: $60-$140 (parts + labor)

DIY Cost: $15-$35 (parts only)

You Save: $45-$105 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.2-0.5 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.