How to Replace the Cabin Air Filter on a 2008 Jeep Grand Cherokee (Glove Box Access)
Step-by-step instructions, tools/parts list, and how to check if your model needs a retrofit kit
How to Replace the Cabin Air Filter on a 2008 Jeep Grand Cherokee (Glove Box Access)
Step-by-step instructions, tools/parts list, and how to check if your model needs a retrofit kit
š§ Grand Cherokee - Cabin Air Filter Inspection/Replacement
On your Grand Cherokee, the cabin air filter (if equipped) lives behind the glove box in the HVAC (heater/AC) housing. Many 2008 Grand Cherokee models were not factory-equipped with a cabin air filter, so the first step is a quick check behind the glove box for a filter access door.
Difficulty Level: Beginner | Estimated Time: 10-30 minutes
ā ļø Safety & Precautions
- ā ļø Turn the ignition OFF and remove the key before working under the dash.
- ā ļø Donāt force plastic tabsāolder trim can crack in cold weather.
- ā ļø Battery disconnect is not required for this job.
š§ Required Tools
You'll need the following tools for this repair:
- Safety glasses
- Nitrile gloves
- Flashlight
- Trim removal tool
- Phillips screwdriver
- Shop towel
š© Required Parts
HowToo sells all the parts you need for this repair:
- Cabin air filter - Qty: 1
- Cabin air filter retrofit kit - Qty: 1 Only if not equipped
š Before You Begin
- Park on level ground and set the parking brake.
- Move the front passenger seat back to give yourself more room.
- Have a flashlight ready so you can clearly see behind the glove box.
šØ Step-by-Step Instructions
Follow these steps in order:
Step 1: Empty and open the glove box
- Remove items from the glove box so nothing falls out.
- Use a flashlight to look along the right side of the glove box for a small ādamperā arm (a little strap that slows the door). Damper = the slow-down strap
Step 2: Release the glove box damper (if equipped)
- If you see a damper strap/arm on the right side, gently pop it off its pin using a trim removal tool (or your fingers if itās loose).
- Use a shop towel to protect trim if you need to pry lightly.
Step 3: Drop the glove box down
- Push inward on both side walls of the glove box (near the top) with your hands so the stops clear the dash opening.
- Let the glove box swing downward slowly.
Step 4: Check for a cabin filter access door
- Use a flashlight and look at the HVAC housing directly behind where the glove box was.
- Look for a rectangular cover/door (often held by small clips or screws).
- If the door is present, continue to Step 5.
- If there is no door/slot for a filter, skip to Step 7 (not factory-equipped).
Step 5: Remove the filter door
- If itās clipped: carefully release the clips using a trim removal tool.
- If itās screwed in: remove screws with a Phillips screwdriver and set them aside.
Step 6: Replace the cabin air filter
- Slide the old filter straight out.
- Use a flashlight to find the airflow arrow on the new filter.
- Install the new filter in the same direction as the arrow indicates (airflow direction matters).
- Reinstall the access door (clips snap in or screws tighten snug with a Phillips screwdriver; no torque spec used here).
Step 7: If no filter is present (common on 2008 models)
- If thereās no filter slot/door, your Grand Cherokee likely wasnāt built with a serviceable cabin air filter.
- If you want filtration, install a cabin air filter retrofit kit (kit contents and procedure vary). Use a flashlight to confirm the HVAC housing has the molded outline where the retrofit door would go before ordering parts.
Step 8: Reinstall the glove box
- Lift the glove box back up, squeeze the sides inward, and guide the stops back into place.
- Reconnect the damper strap/arm (if equipped) by pushing it back onto its pin by hand. Use a trim removal tool only if needed to align it.
ā After Repair
- Start the engine and run the blower on high for 30 seconds.
- Switch between fresh air and recirculation to confirm airflow feels normal and there are no new noises.
- If you notice a musty smell, consider using an HVAC-safe evaporator cleaner (optional).
š° DIY vs Shop Cost
Shop Cost: $80-$160 (parts + labor)
DIY Cost: $15-$45 (parts only)
You Save: $65-$115 by doing it yourself!
Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.3-0.7 hours.
šÆ Ready to get started?
HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.

















