🔧 Camry - Battery Replacement

Your battery is under the hood on the driver's side. Replacing it means disconnecting the old battery, removing the hold-down, swapping in the new one, and reconnecting everything in the correct order.

Difficulty Level: Beginner | Estimated Time: 0.5-1 hour

---

⚠️ Safety & Precautions

• Wear safety glasses and gloves. Battery acid can burn skin and eyes.
• Turn the ignition OFF and remove the key/fob from the cabin.
• Do not let a wrench touch both battery terminals at once.
• Keep metal tools away from the positive terminal.
• Battery memory may reset. Window auto-up and clock settings may need to be relearned.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 10mm wrench
• 10mm socket
• Ratchet
• Battery terminal brush
• Battery carrying strap
• Safety glasses
• Gloves

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• 12V battery - Qty: 1
• Battery terminal protector spray - Qty: 1

---

📋 Before You Begin

• Park on level ground and set the parking brake.
• Turn all accessories off: lights, fan, radio, chargers.
• Make sure you know your radio and clock settings if you want to restore them later.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Open the battery area

• Open the hood and locate the battery on the driver's side.
• If a cover is installed, remove it by hand.

Step 2: Disconnect the negative cable

• Use a 10mm wrench to loosen the negative terminal nut.
• Remove the negative cable and move it aside so it cannot touch the battery.
• Negative first prevents short circuits.

Step 3: Disconnect the positive cable

• Use a 10mm wrench to loosen the positive terminal nut.
• Remove the positive cable and keep it away from metal parts.

Step 4: Remove the hold-down bracket

• Use a 10mm socket and ratchet to remove the battery hold-down clamp.
• Lift the clamp and hardware out of the way.

Step 5: Remove the old battery

• Lift the battery straight up using the battery carrying strap.
• Battery is heavy, so use both hands and lift carefully.

Step 6: Clean the tray and terminals

• Use a battery terminal brush to clean corrosion from the cable ends.
• Wipe the battery tray clean before installing the new battery.
• Clean connections help the new battery last longer.

Step 7: Install the new battery

• Set the new battery in the tray in the same direction as the old one.
• Reinstall the hold-down bracket with the 10mm socket.
• Torque to 7 Nm (62 in-lbs).

Step 8: Reconnect the positive cable

• Install the positive cable first using the 10mm wrench.
• Torque to 5 Nm (44 in-lbs).

Step 9: Reconnect the negative cable

• Install the negative cable last using the 10mm wrench.
• Torque to 5 Nm (44 in-lbs).

Step 10: Protect and test

• Apply battery terminal protector spray if desired.
• Start the engine and verify normal cranking.
• Check that the battery light is off.

---

✅ After Repair

• Reset the clock and radio presets if needed.
• Reinitialize the driver window auto-up/down if it stopped working.
• Let the car idle for a few minutes and confirm stable operation.

---

💰 DIY vs Shop Cost

Shop Cost: $220-$380 (parts + labor)

DIY Cost: $130-$220 (parts only)

You Save: $90-$160 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.5-1 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.