🔧 Town & Country - Rear Turn Signal Bulb Replacement

You’ll remove the rear tail lamp assembly, twist out the turn-signal bulb socket, and swap in a new bulb. This fixes a fast-blink signal, a “bulb out” warning, or a rear turn signal that doesn’t light.

Difficulty Level: Beginner | Estimated Time: 0.5-1.0 hours

---

⚠️ Safety & Precautions

• ⚠️ Turn the ignition OFF and remove the key/fob from the van.
• ⚠️ Let the bulbs cool before touching; they can burn you.
• ⚠️ Wear gloves—skin oils can shorten some bulb life.
• ⚠️ Support the tail lamp so it doesn’t drop and crack.
• Battery disconnect is not required for this repair.

---

🔧 Required Tools

You'll need the following tools for this repair:

• #2 Phillips screwdriver
• Plastic trim removal tool
• Nitrile gloves
• Safety glasses

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Rear turn signal bulb - Replace in pairs - Qty: 2

---

📋 Before You Begin

• Park on level ground and set the parking brake.
• Open the liftgate for access to the tail lamp fasteners.
• Tip: Do one side at a time.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Access the tail lamp fasteners

• Open the liftgate.
• Locate the two Phillips screws on the inboard edge of the tail lamp (the edge closest to the liftgate opening).
• Use a #2 Phillips screwdriver to remove both screws.

Step 2: Remove the tail lamp assembly

• Hold the lamp with one hand, then pull the lamp straight rearward (toward you).
• If it feels stuck, use a plastic trim removal tool to gently start the lamp moving at the edges. Do not pry hard.
• Tip: A gentle wiggle helps release the locating pins.

Step 3: Remove the turn signal bulb socket

• On the back of the tail lamp, find the socket for the turn signal.
• Twist the socket counterclockwise about 1/4 turn by hand (use nitrile gloves for grip) and pull the socket out.
• Bulb socket: the plastic holder that locks into the lamp by twisting.

Step 4: Replace the bulb

• Pull the old bulb straight out of the socket (it’s a wedge-style bulb).
• Push the new bulb straight into the socket until fully seated.
• Avoid touching the glass with bare fingers; use nitrile gloves.

Step 5: Reinstall the socket and test

• Insert the socket back into the tail lamp and twist clockwise to lock.
• Turn the ignition ON and test the rear turn signal.
• If it doesn’t light, turn ignition OFF and re-check that the bulb is fully seated.

Step 6: Reinstall the tail lamp assembly

• Align the locating pins on the lamp with the body holes, then press the lamp straight into place.
• Install the two screws using a #2 Phillips screwdriver.
• Torque to 2 Nm (18 in-lbs) (snug only—do not overtighten).

---

✅ After Repair

• Verify left and right rear turn signals work normally (no fast-blink).
• Check hazard lights (all corners flashing).
• Confirm the tail lamp sits flush with the body and liftgate closes cleanly.

---

💰 DIY vs Shop Cost

Shop Cost: $60-$140 (parts + labor)

DIY Cost: $10-$30 (parts only)

You Save: $50-$110 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.5-1.0 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.