🔧 Sequoia - Front Windshield Wiper Blade Replacement

You’ll be removing the old front wiper blades from the wiper arms and snapping the new blades on. Worn blades cause streaking, chattering, and poor visibility, especially in rain.

Difficulty Level: Beginner | Estimated Time: 0.25-0.5 hours

---

⚠️ Safety & Precautions

• 🛑 Turn the ignition OFF before lifting the wiper arms.
• 🛑 Place a towel on the lower windshield/cowl area to protect paint and glass.
• 🛑 Never let a bare wiper arm snap onto the windshield (it can crack the glass).
• 🛑 Work carefully in cold weather; blades and clips can be brittle.

---

🔧 Required Tools

You'll need the following tools for this repair:

• Microfiber towel
• Nitrile gloves
• Safety glasses
• Small flathead screwdriver
• Step stool

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Front wiper blades - Replace in pairs - Qty: 2
• Windshield washer fluid - Qty: 1 gallon

---

📋 Before You Begin

• Park your Sequoia on level ground and set the parking brake.
• Turn the ignition OFF and make sure the wipers are not mid-swipe.
• Lay a microfiber towel along the bottom edge of the windshield.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Lift the wiper arms

• Use a step stool if needed to reach comfortably.
• Lift the driver-side wiper arm away from the windshield until it stays up.
• Keep one hand on the arm.

Step 2: Identify your blade connector type

• Look where the blade meets the end of the wiper arm.
• Most Sequoia front wipers use a hook-style (“J-hook”) connector, but some blades use a pinch-tab style adapter.

Step 3: Remove the old blade (Hook/J-hook style)

• Rotate the wiper blade so it’s roughly perpendicular to the wiper arm.
• Press the small release tab on the blade connector using your thumb, or gently help it with a small flathead screwdriver.
• Slide the blade down toward the base of the hook, then unhook it and remove it.

Step 4: Remove the old blade (Pinch-tab style)

• Squeeze the two side tabs on the connector with your fingers.
• If it’s stuck, gently assist one tab at a time with a small flathead screwdriver.
• Slide the blade straight off the arm.

Step 5: Install the new blade

• Compare the new blade to the old one for matching length and connector style.
• Attach the new blade to the arm:
  • Hook/J-hook: feed the hook into the adapter and pull until it clicks/locks.
  • Pinch-tab: slide the adapter onto the arm until it clicks.
• Gently tug on the blade to confirm it’s locked on.

Step 6: Lower the arm safely

• Hold the wiper arm and slowly lower the blade onto the windshield.
• Repeat Steps 1–6 for the passenger-side wiper.

Step 7: Top off and test

• Open the washer reservoir and add windshield washer fluid.
• Start the engine and run washers/wipers for 5–10 sweeps.
• Check for streaking and make sure both blades park correctly.

---

✅ After Repair

• Verify both blades wipe evenly without chatter.
• Recheck that each blade is fully latched by lightly tugging at the connector.
• Clean the windshield with glass cleaner if you still see haze or streaks.

---

💰 DIY vs Shop Cost

Shop Cost: $40-$90 (parts + labor)

DIY Cost: $20-$60 (parts only)

You Save: $20-$30 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.2-0.4 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.