🔧 Front Turn Signal Bulbs - Replacement

Replacing the front turn signal bulbs means removing access to the front lamp housing, swapping the bulb, and confirming the signal flashes correctly. On your Stinger, this is a simple job if the front indicators use replaceable bulbs; if yours are factory LED, the bulb is not serviceable and the lamp assembly must be replaced.

Difficulty Level: Beginner | Estimated Time: 0.5-1 hour

---

⚠️ Safety & Precautions

• Turn the ignition off and let the lamps cool before touching them.
• Do not touch the glass of a halogen bulb with bare fingers; oil can shorten bulb life.
• Use a towel or gloves when handling the new bulb.
• If your Stinger has LED front indicators, the bulb cannot be replaced separately.
• No battery disconnect is required for this repair.

---

🔧 Required Tools

You'll need the following tools for this repair:

• Flat trim tool
• 10mm socket
• 1/4-inch ratchet
• Gloves
• Safety glasses
• Flashlight

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Front turn signal bulb - Qty: 2

---

📋 Before You Begin

• Park on level ground and set the parking brake.
• Turn the headlights and ignition off.
• Open the hood and secure it fully.
• Work on one side at a time.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Open the hood and locate the headlamp access area

• Use the hood release inside the cabin, then lift the hood and secure it.
• Use a flashlight to find the rear of the headlamp area behind the front bumper cover.

Step 2: Remove the front access cover or air duct if equipped

• Use a flat trim tool to release any plastic push clips or covers blocking access.
• If a small duct or cover is held by fasteners, use the 10mm socket and 1/4-inch ratchet to remove it.
• Keep fasteners in a small tray.

Step 3: Reach the turn signal bulb socket

• Reach behind the headlamp housing and locate the turn signal bulb socket.
• Twist the socket counterclockwise by hand to remove it from the lamp housing.

Step 4: Replace the bulb

• Press the old bulb gently into the socket and turn it out, or pull it straight out if it is a wedge-style bulb.
• Install the new front turn signal bulb into the socket.
• Make sure it is seated fully and straight.

Step 5: Reinstall the socket and test

• Insert the socket back into the headlamp housing and twist clockwise to lock it.
• Turn on the turn signal and check for normal flashing on that side.
• If the bulb does not light, remove it and recheck the fit.

Step 6: Reinstall covers and repeat on the other side

• Reinstall any covers or ducts using the 10mm socket and 1/4-inch ratchet.
• Repeat the same steps on the opposite side if you are replacing both bulbs.

---

✅ After Repair

• Start the car and verify both front turn signals flash correctly.
• Check the hazard lights too.
• Look at each bulb from the front to confirm equal brightness.
• If the turn signal blinks fast, the bulb may not be seated correctly or may be the wrong type.

---

💰 DIY vs Shop Cost

Shop Cost: ₹1,500-₹4,000 (parts + labor)

DIY Cost: ₹300-₹1,200 (parts only)

You Save: ₹1,200-₹2,800 by doing it yourself!

Shop labor rates vary but typically run ₹2,000-₹4,000/hour. This repair takes a shop approximately 0.5-1 hour.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.