🔧 Accord - Front Turn Signal Bulb Replacement

You’ll replace the front turn signal bulbs by accessing the bulb sockets from behind each headlight with the hood open. This is a quick job, and it usually doesn’t require removing the headlight or bumper.

Difficulty Level: Beginner | Estimated Time: 0.3-0.8 hours

---

⚠️ Safety & Precautions

• ⚠️ Turn lights OFF and remove the key before starting.
• ⚠️ Let the headlight area cool if the lights were recently on.
• ⚠️ Wear gloves—bulbs can be hot and the glass can break if squeezed.
• ⚠️ Do not touch the new bulb’s glass with bare fingers (skin oil can shorten bulb life).
• 🔋 Battery disconnect is not required for this bulb replacement.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 10mm socket
• 3/8" ratchet
• 3" socket extension
• Trim clip removal tool
• Flashlight
• Nitrile gloves
• Safety glasses

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Front turn signal bulb (amber, dual-filament) - Replace in pairs - Qty: 2

---

📋 Before You Begin

• Park on level ground and set the parking brake.
• Turn the headlight switch to OFF and make sure the turn signals are OFF.
• Open the hood and have your flashlight ready.
• Tip: Do one side at a time.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Access the back of the headlight

• Open the hood and look behind the headlight assembly on the side you’re replacing.
• Use a flashlight to find the turn signal/parking light socket (it will be a twist-lock socket going into the headlight housing).

Step 2: Create a little working room (only if needed)

• If your hand doesn’t fit comfortably, remove the plastic air intake snorkel/duct near the headlight.
• Use a trim clip removal tool to pop up any push-clips (a push-clip is a plastic fastener with a center pin that lifts up first).
• If there are small bolts holding a bracket/duct, remove them using a 10mm socket, 3/8" ratchet, and 3" socket extension.
• Tip: Set clips/bolts in a cup.

Step 3: Remove the turn signal bulb socket

• Grip the socket firmly and rotate it counterclockwise about 1/4 turn.
• Pull the socket straight back to remove it from the headlight housing.
• Torque note: No torque specs are used here—this is a hand-tight twist-lock socket.

Step 4: Remove the old bulb

• Wear nitrile gloves.
• Pull the bulb straight out of the socket (it’s a push-in style on this setup).

Step 5: Install the new bulb

• With nitrile gloves on, push the new bulb straight into the socket until fully seated.
• If you accidentally touch the glass, wipe it clean and dry before installing.

Step 6: Reinstall the socket

• Insert the socket back into the headlight housing.
• Rotate clockwise about 1/4 turn until it stops (snug by hand).

Step 7: Reinstall any removed duct/clips

• Reposition the duct/bracket.
• Reinstall any bolts using a 10mm socket, 3/8" ratchet, and 3" socket extension (snug—do not over-tighten into plastic).
• Reinstall push-clips using the trim clip removal tool to align them, then press them in by hand.

Step 8: Repeat on the other side

• Repeat Steps 1–7 for the opposite front turn signal bulb.

---

✅ After Repair

• Turn the ignition to ON and test left and right turn signals.
• Verify the front bulbs blink at a normal speed (fast blinking usually means a bulb isn’t working or isn’t seated).
• Turn on the parking lights and confirm the same bulbs illuminate steadily (if your setup uses a dual-filament bulb).

---

💰 DIY vs Shop Cost

Shop Cost: $80-$160 (parts + labor)

DIY Cost: $10-$30 (parts only)

You Save: $50-$140 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.3-0.8 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.