🔧 Front Brake Pads - Replacement

The front pads on your Accord are a straightforward brake service, but you need to work carefully and keep everything clean. The main job is to remove the caliper, swap the pads, inspect the rotor, then reassemble and seat the brakes properly.

Difficulty Level: Intermediate | Estimated Time: 1.5-2.5 hours

---

⚠️ Safety & Precautions

• Work on a flat surface and chock the rear wheels before lifting the front.
• Use jack stands. Never rely on the jack alone.
• Do not press the brake pedal while the caliper is removed.
• Brake parts and rotors can be hot if the car was driven recently.
• Keep grease, oil, and brake fluid off the pads and rotor.
• Your Accord has an electronic parking brake, but front pad replacement does not require EPB service mode.
• Brake dust can be harmful. Wear a mask if the dust is heavy.

---

🔧 Required Tools

You'll need the following tools for this repair:

• Floor jack (rated 3-ton minimum)
• Jack stands
• Wheel chocks
• 19mm socket
• 14mm socket
• Ratchet
• Breaker bar
• Torque wrench
• Brake caliper compression tool (specialty)
• Flat-blade screwdriver
• Wire brush
• Micrometer or rotor gauge
• Brake cleaner
• Shop towels
• Safety glasses
• Nitrile gloves

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Front brake pad set - Qty: 1
• Brake hardware kit - Qty: 1
• Brake cleaner - Qty: 1 can
• Anti-squeal brake lubricant - Qty: 1

---

📋 Before You Begin

• Park on level ground and set the parking brake.
• Loosen the front wheel lug nuts before lifting the car.
• Keep the ignition off so the brake system does not activate.
• Open the hood and check the brake fluid level before pushing the caliper pistons back. If the reservoir is full, remove a little fluid first.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Lift the front of the vehicle

• Use a floor jack at the front lift point and raise the car.
• Set the car securely on jack stands.
• Remove the front wheel with a 19mm socket.

Step 2: Remove the caliper

• Use a 14mm socket to remove the two caliper slide bolts.
• Lift the caliper off the bracket carefully.
• Hang the caliper with a hook or wire so the hose is not stretched.

Step 3: Remove the old pads and hardware

• Pull the old brake pads out of the caliper bracket.
• Remove the pad clips and hardware.
• Use a wire brush to clean rust from the bracket contact points.
• Clean metal helps prevent squeaks.

Step 4: Compress the caliper piston

• Use a brake caliper compression tool (specialty) to push the piston back into the caliper slowly.
• Watch the brake fluid reservoir while compressing the piston.
• Make sure the piston face sits square and flush.

Step 5: Install the new hardware and pads

• Install the new pad clips from the brake hardware kit.
• Apply a thin layer of anti-squeal brake lubricant only on pad contact points and backing plates, not on friction material.
• Install the new brake pads into the bracket.

Step 6: Reinstall the caliper

• Slide the caliper back over the new pads.
• Install the caliper slide bolts with the 14mm socket.
• Torque to 32 Nm (24 ft-lbs).

Step 7: Reinstall the wheel

• Put the wheel back on and thread the lug nuts by hand first.
• Lower the car enough so the tire touches the ground lightly.
• Use a torque wrench with a 19mm socket to tighten the lug nuts in a crisscross pattern.
• Torque to 108 Nm (80 ft-lbs).

Step 8: Repeat on the other side

• Replace the pads on the other front wheel too.
• Always replace brake pads in pairs.

---

✅ After Repair

• Press the brake pedal slowly several times until it feels firm.
• Check the brake fluid level and top off if needed.
• Start the car and make sure no brake warning lights stay on.
• Test the brakes at low speed in a safe area.
• For the first 200-300 miles, avoid hard stops unless needed.

---

💰 DIY vs Shop Cost

Shop Cost: ₹8,000-₹16,000 (parts + labor)

DIY Cost: ₹3,500-₹8,000 (parts only)

You Save: ₹4,500-₹8,000 by doing it yourself!

Shop labor rates vary but typically run ₹2,500-₹6,000/hour. This repair takes a shop approximately 1.5-2.5 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.