🔧 Canyon - Headlight Bulb Replacement

On your Canyon, the “headlight” can mean the low beam, high beam, or the daytime running light/turn signal—each uses a different bulb and access method. I can walk you through the exact steps, but I need to confirm which lighting system you have so you don’t buy the wrong bulbs or remove unnecessary parts.

Difficulty Level: Intermediate | Estimated Time: 0.8-1.5 hours

---

⚠️ Safety & Precautions

• ⚠️ Turn lights OFF and let the housing cool before touching any bulb.
• ⚠️ Don’t touch halogen bulb glass with bare fingers; skin oils shorten bulb life.
• ⚠️ If equipped with HID/LED, don’t unplug components with lights on; high voltage may be present.

---

🔧 Required Tools

You'll need the following tools for this repair:

• Nitrile gloves
• Safety glasses
• Flashlight
• Trim clip removal tool
• Ratchet
• 7mm socket
• 10mm socket
• Small flat-blade screwdriver

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Headlight bulb(s) - Qty: 2

---

📋 Before You Begin

• Park on level ground, shift to Park, and set the parking brake.
• Turn the headlight switch to OFF and remove the key/fob from the cab.
• Open the hood and support it securely.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Confirm the exact bulbs you’re replacing

• Look at the back of the headlight housing and identify which socket you’re changing (low beam vs high beam vs DRL/turn).
• Use flashlight to read the bulb marking on the old bulb or the label on the housing (examples might look like “H11”, “9005”, “7444”, etc.).
• We’ll match parts to the marking you find.

Step 2: Access the rear of the headlamp (varies by equipment)

• If your Canyon has clear space behind the headlamp, you may be able to reach the bulb directly by hand (wear nitrile gloves).
• If access is tight, you may need to remove air ducting or the washer fill neck for that side:
• Use trim clip removal tool to pop plastic retainers.
• Use ratchet with 7mm socket or 10mm socket to remove small bolts as needed.

Step 3: Remove the old bulb

• Unplug the electrical connector from the bulb socket. If it has a lock tab, press the tab using a small flat-blade screwdriver gently.
• Rotate the bulb counterclockwise (usually about a quarter turn) and pull it straight out.
• If it’s an HID/LED module (not a simple twist-in bulb), stop here—tell me and I’ll give the correct procedure.

Step 4: Install the new bulb

• Put on nitrile gloves and handle the new bulb by the base only.
• Insert the bulb into the housing, align the tabs, then rotate clockwise to lock.
• Reconnect the electrical connector until it clicks.

Step 5: Repeat on the other side

• Repeat Steps 2–4 for the opposite headlight bulb.
• Reinstall any ducts/covers you removed using the same 7mm socket, 10mm socket, and trim clip removal tool.

---

✅ After Repair

• Turn the headlights ON and confirm both sides work on the correct setting (low beam / high beam / DRL).
• Check for flicker and make sure the bulb is fully seated (a loose bulb can look dim or aim wrong).
• If the beam aim looks off after replacement, tell me and I’ll walk you through the aim check for your Canyon.

---

💰 DIY vs Shop Cost

Shop Cost: $120-$260 (parts + labor)

DIY Cost: $30-$140 (parts only)

You Save: $90-$120 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.8-1.5 hours.

---

🎯 Ready to get started?

Quick check so I can give you the exact bulb types and the exact access steps for your Canyon:

• ❓ Are you replacing low beams, high beams, or both?
• ❓ Do your headlights have a simple twist-in bulb (halogen) or a factory HID/LED module (often says “D” bulb or has a ballast/module)?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.