🔧 Engine Oil & Filter - Oil Change

Changing the oil and filter on your CR-V keeps the engine lubricated, cool, and clean. Honda recommends 0W-20 full synthetic oil for this engine, and the filter should be replaced every oil change for best protection.

Difficulty Level: Beginner | Estimated Time: 1-1.5 hours

---

⚠️ Safety & Precautions

• Work on a level surface and set the parking brake.
• The engine and exhaust can be hot. Let the vehicle cool before draining oil.
• Use jack stands if you raise the front. Never rely on a jack alone.
• Keep used oil off the ground. Clean spills right away.
• Dispose of used oil and filter at a recycling center or auto parts store.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 17mm socket
• 3/8-inch ratchet
• Oil filter wrench
• Drain pan
• Funnel
• Floor jack (rated 3-ton minimum)
• Jack stands
• Wheel chocks
• Torque wrench
• Shop towels
• Safety glasses
• Nitrile gloves

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Engine oil (0W-20 full synthetic) - Qty: 5 quarts
• Oil filter - Qty: 1
• Drain plug crush washer - Qty: 1

---

📋 Before You Begin

• Park on level ground and engage the parking brake.
• Warm the engine for a few minutes if you want faster draining, then shut it off.
• Let the oil cool enough to work safely.
• Open the hood and remove the oil fill cap to help the oil drain faster.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Raise and secure the front

• Use a floor jack to lift the front of the vehicle at the approved jacking point.
• Place it on jack stands before going underneath.
• Chock the rear wheels with wheel chocks.
• Never work under a car supported only by a jack.

Step 2: Remove the oil drain plug

• Position the drain pan under the oil pan.
• Use a 17mm socket and 3/8-inch ratchet to remove the drain plug.
• Let the oil drain fully for several minutes.
• Replace the drain plug crush washer before reinstalling the plug.

Step 3: Remove the oil filter

• Move the drain pan under the filter area.
• Use an oil filter wrench to loosen and remove the old filter.
• Make sure the old rubber gasket comes off with the filter.
• A stuck gasket can cause a leak.

Step 4: Install the new oil filter

• Lightly coat the new filter gasket with fresh engine oil.
• Spin the new filter on by hand until the gasket touches.
• Then tighten it 3/4 turn by hand. Do not over-tighten.

Step 5: Reinstall the drain plug

• Install the drain plug with the new crush washer by hand first.
• Use a torque wrench with a 17mm socket to tighten the drain plug to 39 Nm (29 ft-lbs).

Step 6: Fill with new engine oil

• Lower the vehicle to level ground.
• Use a funnel to add about 4.4 quarts of 0W-20 full synthetic oil.
• Install the oil fill cap.

Step 7: Check the oil level

• Start the engine and let it run for 30 seconds.
• Shut the engine off and wait 5 minutes.
• Use the dipstick to check the level.
• Add small amounts of oil until the level is at the full mark.

---

✅ After Repair

• Check underneath for leaks at the drain plug and filter.
• Verify the oil level again after a short drive.
• Reset the maintenance minder if needed using the instrument cluster menu.
• Recheck the oil level over the next day if you want extra peace of mind.

---

💰 DIY vs Shop Cost

Shop Cost: $80-$140 (parts + labor)

DIY Cost: $35-$65 (parts only)

You Save: $45-$75 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.8-1.0 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.