🔧 Engine Oil and Oil Filter - Replacement

Your Silverado needs a drain, filter change, and refill with the correct oil spec. This service helps protect the engine, keep oil pressure stable, and remove contaminants that build up over time.

Difficulty Level: Beginner | Estimated Time: 1-1.5 hours

---

⚠️ Safety & Precautions

• Engine oil can be very hot. Let the engine cool before starting.
• Use jack stands anytime the truck is raised. Never rely on a floor jack alone.
• Set the parking brake and chock the rear wheels before lifting the front.
• Keep oil off belts, hoses, and the exhaust.
• Dispose of used oil and filter properly. Do not pour oil on the ground.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 15mm socket
• Ratchet
• Oil filter wrench
• Drain pan
• Funnel
• Floor jack (rated 3-ton minimum)
• Jack stands
• Wheel chocks
• Gloves
• Safety glasses
• Shop rags
• Torque wrench

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Engine oil (0W-20 full synthetic dexos1 Gen 2) - Qty: 6 quarts
• Oil filter - Qty: 1
• Drain plug washer - Qty: 1

---

📋 Before You Begin

• Park on level ground.
• Shift to Park and set the parking brake.
• Let the engine cool for at least 20-30 minutes.
• Have the new filter and oil ready before draining.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Raise and secure the front of the truck

• Use a floor jack to lift the front enough to work safely.
• Place jack stands under the proper front frame points.
• Lower the truck onto the stands and check stability.
• Give the truck a gentle shake.

Step 2: Remove the oil fill cap

• Open the hood and remove the oil fill cap by hand.
• This helps the oil drain faster.

Step 3: Drain the engine oil

• Place the drain pan under the oil pan drain plug.
• Use a 15mm socket and ratchet to remove the drain plug.
• Let the oil drain fully.
• Inspect the drain plug and replace the washer if needed.
• Reinstall the drain plug and Torque to 25 Nm (18 ft-lbs).

Step 4: Remove the oil filter

• Move the drain pan under the filter area.
• Use an oil filter wrench to loosen the filter.
• Spin the filter off by hand once it breaks loose.
• Be ready for oil to spill from the filter.

Step 5: Install the new oil filter

• Wipe the filter mounting surface clean with a shop rag.
• Lightly coat the new filter gasket with fresh engine oil.
• Spin the new filter on by hand until the gasket touches.
• Then tighten it about 3/4 turn more by hand.
• Do not overtighten the filter.

Step 6: Refill the engine with oil

• Place a funnel in the oil fill hole.
• Add about 5.5 quarts of the correct oil first.
• Install the oil fill cap.
• Start the engine and let it idle for 30 seconds.

Step 7: Check for leaks and set final oil level

• Shut the engine off and wait 5 minutes.
• Check under the truck for leaks at the drain plug and filter.
• Check the dipstick and top off oil as needed.
• Final capacity is usually about 6 quarts with filter.

Step 8: Reset the oil life monitor

• Turn the ignition on without starting the engine.
• Use the Driver Information Center controls to find Oil Life.
• Press and hold the reset button until oil life returns to 100%.
• Reset only after the service is complete.

---

✅ After Repair

• Check the oil level again after your first drive.
• Look for drips under the truck after parking.
• Recheck the drain plug and filter area if you see any oil.

---

💰 DIY vs Shop Cost

Shop Cost: $90-$160 (parts + labor)

DIY Cost: $45-$75 (parts only)

You Save: $45-$85 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.7-1.0 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.