🔧 Engine Oil & Oil Filter - Replacement

Changing the oil and filter on your Silverado keeps the engine lubricated, cool, and clean. This truck uses a conventional drain plug and a spin-on oil filter, so the job is straightforward if you work carefully and keep everything clean.

Difficulty Level: Beginner | Estimated Time: 1-1.5 hours

---

⚠️ Safety & Precautions

• Work on a level surface and set the parking brake.
• Let the engine cool enough to avoid burns from hot oil and exhaust parts.
• Use jack stands if you lift the truck. Never rely on a jack alone.
• Keep oil away from belts, hoses, and the drive belt pulley area.
• Battery disconnect is not required for this repair.

---

🔧 Required Tools

You'll need the following tools for this repair:

• 15mm socket
• Ratchet
• Oil filter wrench
• Drain pan
• Funnel
• Torque wrench
• Floor jack (rated 3-ton minimum)
• Jack stands (rated for truck weight)
• Wheel chocks
• Safety glasses
• Nitrile gloves
• Shop towels

---

🔩 Required Parts

HowToo sells all the parts you need for this repair:

• Engine oil (5W-30 full synthetic) - Qty: 6 quarts
• Oil filter - Qty: 1
• Drain plug gasket - Qty: 1

---

📋 Before You Begin

• Park on level ground and engage the parking brake.
• Warm the engine for a few minutes, then shut it off. Warm oil drains faster.
• If the truck is lifted, support it securely with jack stands.
• Have the new filter and drain plug gasket ready before you start.

---

🔨 Step-by-Step Instructions

Follow these steps in order:

Step 1: Raise and secure the truck

• Use the floor jack to raise the front of the truck enough to reach the drain plug and filter.
• Support it with jack stands and chock the rear wheels.
• Give the truck a gentle shake.

Step 2: Remove the oil fill cap

• Open the hood and remove the engine oil fill cap by hand.
• This helps the oil drain smoothly.

Step 3: Drain the old oil

• Place the drain pan under the oil pan drain plug.
• Use the 15mm socket and ratchet to remove the drain plug.
• Let the oil drain completely.
• Inspect the drain plug threads and replace the gasket if needed.
• Torque to 25 Nm (18 ft-lbs) when reinstalling the drain plug.

Step 4: Remove the old oil filter

• Move the drain pan under the oil filter area.
• Use the oil filter wrench to loosen and remove the filter.
• Make sure the old rubber gasket comes off with the filter. If it sticks to the engine, remove it by hand.
• Check for a stuck gasket every time.

Step 5: Install the new oil filter

• Wipe the filter mounting surface clean with a shop towel.
• Put a thin film of fresh oil on the new filter gasket.
• Spin the new filter on by hand until the gasket touches, then tighten it as directed on the filter.
• Torque to 25 Nm (18 ft-lbs) if the filter spec is provided on the filter body.

Step 6: Reinstall the drain plug

• Reinstall the drain plug by hand first to avoid cross-threading.
• Use the 15mm socket and torque wrench to tighten it.
• Torque to 25 Nm (18 ft-lbs).

Step 7: Add new engine oil

• Place a funnel in the oil fill opening.
• Add about 5.5 quarts first, then check the dipstick.
• Top off slowly until the level reaches the full mark.
• Total capacity is about 6 quarts with filter.

Step 8: Start and inspect

• Start the engine and let it run for 30-60 seconds.
• Check underneath for leaks at the drain plug and filter.
• Shut the engine off and wait a few minutes, then recheck the dipstick and top off if needed.

---

✅ After Repair

• Verify the oil level on the dipstick with the truck on level ground.
• Check again for leaks after a short test drive.
• Reset the oil life monitor: turn ignition ON without starting, then press the accelerator pedal fully 3 times within 5 seconds.
• Confirm the oil life shows 100% after the reset.

---

💰 DIY vs Shop Cost

Shop Cost: $90-$160 (parts + labor)

DIY Cost: $35-$65 (parts only)

You Save: $55-$95 by doing it yourself!

Shop labor rates vary but typically run $100-$150/hour. This repair takes a shop approximately 0.7-1.0 hours.

---

🎯 Ready to get started?

HowToo makes it easy: same-day/2-day shipping on every part, plus all the tools and specialty tools you need! Check out the parts and tools sections below to add everything to your cart.